Inverter Ingeteam INGECON SUN Storage 1Play 3 TL 3kW for grid connection and storage #31051010

Inverter Ingeteam INGECON SUN Storage 1Play 3 TL 3kW for grid connection and storage #31051010

Inverter Ingeteam INGECON SUN Storage 1Play 3 TL 3kW for grid connection and storage #31051010

Innovative Ingeteam SUN Storage 1Play 3 TL 3kW Inverter with intelligent storage management ideal for photovoltaic systems for grid connection or grid switch.
Price:
€3,122.90
Listing:
€3,674.00
You Save:
€551.10 (15%)

Description

Note: the article is available within 10 days from date of order.

Inverter
CEI 0-21 Certified

SMART SOLUTION FOR BALANCE BETWEEN ENERGY GENERATION, CONSUMPTION AND STORAGE


The INGECON® SUN STORAGE 1Play battery inverters are single-phase, two-way units that can either be used in off-grid systems or connected to the general supply network. The INGECON® SUN STORAGE 1Play battery inverter generates an off-grid AC network and manages the power achieving an optimum balance between production, storage and consumption.
PV Input: The INGECON® SUN STORAGE 1Play inverters incorporate a PV input. Thanks to it, a PV array with up to 11.5 kWp maximum power can be connected directly to the unit without using a solar inverter.
Featuring an advanced battery management technology, it ensures the maximum life of the storage system, by controlling constantly the battery temperature using a three-wire PT100 sensor. In case of need, it connects and controls an auxiliary generator.
Thanks to its auxiliary AC input, the grid or a back-up diesel generator can be connected to the inverter. It is possible to start-up the inverter by using this input in order to charge the batteries.
This inverter is fully compatible with INGECON® SUN PV inverters. Furthermore, the scale of the system created and managed by the INGECON® SUN STORAGE 1Play TL can be increased through the parallel connection of grid connected inverters to the AC grid.

This new inverter features 4 operating modes:

Stand-alone mode: The inverter generates an AC grid and the renewable energy source is used to feed the loads and to charge the batteries. The auxiliary source (a diesel genset or the public grid) is only connected when the batteries' state of charge is lower than a certain threshold. As a special operating case, it is posible to implement the Direct Panel Mode, for those installations without an energy storage system. In this mode, the system only operates when the solar resource is available.
Back-up mode: The battery inverter is connected to the public grid when it is present. Thus, if there is an energy surplus, it could be injected into the grid. The energy stored would only be used when the public grid is not available. This mode makes it possible to implement peak shaving strategies in order to reduce the contracted power.
Self-consumption mode: The inverter operates as a grid-tied one. If there is an energy surplus, it will be used to charge the batteries or it may be injected into the grid if the batteries are fully charged. If the loads demand more energy than the one produced by the renewable source, the batteries will satisfy the demand, increasing the self-consumption ratio. This mode makes it possible to implement peak shaving strategies in order to reduce the contracted power.
Grid support mode: In combination with an external wattmeter and the INGECON® EMS Board or the INGECON® EMS Manager, the inverter is able to adapt the output power from the PV plant to a pre-established value, in order to maintain a constant power output or to control the ramp rate. Furthermore, this operating mode makes it possible to implement peak-shaving strategies to reduce the electricity bill by decreasing the contracted power.

Standard 3 year warranty.

MAIN FEATURES
Maximum efficiency: 96%.
IP65 protection rating for outdoor installation.
Available with or w/o galvanic isolation transformer.
Suitable for three-phase configuration up to 18 kW (AC).
CAN communication for BMS (Battery Management Systems).
2 configurable potential-free outputs, some for the connection and disconnection of a back-up genset.
Built-in DC pre-charge system.
Built-in battery temperature measurement circuit. PT100 (3-wire) needed.

PV Input (DC)
PV array max. power 7.5 kWp
Voltage range MPP for stand-alone mode 300 - 480 V
Voltage range MPP for grid-connected modes (1) 330 - 480 V
Maximum open circuit voltage 550 V
Maximum current 20 A
Inputs 2
MPPT 1

Battery Input (DC)
Voltage range with PV installation (2) 40 - 300 V
Voltage range without PV installation (2) 40 - 450 V
Maximum charge / discharge current 50 A
Battery type Lead, Ni-Cd, Li-ion

Generator / Grid Input (AC)
Rated voltage 230 V
Voltage range 172 - 264 V
Rated frequency 50 / 60 Hz
Frequency range 40 - 70 Hz
Charge current range 0 - 13 A
Generator or grid maximum power 11.500 W

Output (AC)
Rated power 3 kW
Current 13 A
Rated voltage 200 - 240 V
Rated frequency 50 / 60 Hz

Efficiency
Maximum efficiency 95.5%

General Information
Stand-by consumption <10 W <10 W
Ambient temperature -20 ºC to +65 °C -20 ºC to +65 °C
Relative humidity (non-condensing) 0 - 95% 0 - 95%
Protection class IP65

To download the installation manual:
http://www.ingeteam.it/userfiles/allegati/ingecon_sun_storage_1play__installation_manual_multi_abh2013iqm01__1431442176.pdf

IMPORTANT NOTE:
The reduced VAT is reserved for PRIVATE INDIVIDUALS, end users and qualified photovoltaic and thermal energy installers or heat production INSTALLED IN ITALY.  After purchase, kindly complete and return the VAT declaration form together with a copy of an ID document:
Declaration Form
In case you do not have the right to the tax deduction (DEALERS) kindly contact us in advance so that an invoice with 22% VAT can be issued as per the law in force. In the absence of receipt of the declaration the order cannot be shipped as a copy of the VAT declaration form must by law be attached to the company invoice.
The declaration form and ID document must be sent to: 
iva-agevolatashopenergia.com or fax +39 0431 687013.

 

Downloads