Hempel High Protect Two-component A+B Primer 2,5Lt Grey #456COL037

Hempel High Protect Two-component A+B Primer 2,5Lt Grey #456COL037
  • Hempel High Protect Two-component A+B Primer 2,5Lt Grey #456COL037
  • Hempel High Protect Two-component A+B Primer 2,5Lt Grey #456COL037

Hempel High Protect Two-component A+B Primer 2,5Lt Grey #456COL037

HEMPEL HIGH PROTECT is a two component epoxy primer amino high build, solvent free. It forms a hard, tough and water-resistant. As a primer below the waterline of fiberglass boats and steel.
Price:
€120.10
Listing:
€160.13
You Save:
€40.03 (25%)

Description

MORE INFORMATION

Pack of 2.5Lt. Grey.

HIGH PROTECT A + B PRIMER

PHYSICAL CONSTANTS:

Finish: High gloss
Volume solids,% 100
Theoretical coverage: 2.9 m2 / l [116.3 sq.ft. / US gallon] - 350 micron / 14 mils
Flash point: 74 ° C [165.2 ° F]
Specific weight: 1.3 kg / liter [10.5 lb / US gallons]
Touch dry: 10-12 hour (s) 20 ° C / 68 ° F, 22 to 27 hours at 10 ° C / 50 ° F
Fully cured: 7 days (i) 20 ° C / 68 ° F, 14 days (i) at 10 ° C / 50 ° F
VOC content: 10 g / l [0.1 lb / US gallons]

APPLICATION DETAILS:

Mixing ratio: 3: 2 by volume
Application method: Airless / brush / sponge roller
Thinner, (volume max): Do not dilute
Pot life: 45 minutes (i) 20 ° C / 68 ° F, 60 minutes at 15 ° C / 59 ° F
Hole nozzle: 0.023 "
Nozzle pressure: 250 bar [3625 psi] (Airless spray data are indicatrivi and subject to adjustment)
Cleaning equipment: HEMPEL'S THINNER 08451 The roller is discarded after use.
Dry thickness indicated 350 micron [14 mils]
Thick wet indicated 350 micron [14 mils]
Recoat interval, min to specification.
Recoat interval, max As per specification.

SURFACE PREPARATION:

Wash the area to be treated with HEMPEL'S PRE-CLEAN 67602 as shown in the instructions and rinse with fresh water. Remove salt and other contaminants by cleaning with fresh water at high pressione.Fibra glass: The surface should be roughened with a roughness uniform (sandpaper, grit 80-100). Remove the polvere.Acciaio: Making your blasting to Sa 2½, ISO 8501-1: 2007, surface profile corresponding to Rugotest No. 3, BN 11.

CONDITIONS OF APPLICATION:

Use only when the application and curing take place at temperatures higher than 10 ° C / 50 ° F. The temperature of the paint must be equal to 15 ° C or higher. When applying, the surface must be perfectly clean, dry and temperature must be above the dew point to prevent the formation of condensa.Fibra glass: For repairs of osmosis, apply at least 2 layers with dry film thickness of 350 microns each (at least 4 layers with dry film thickness of 150 microns each for roller applications). For preventive treatments, apply at least one layer with a dry film thickness of 350 microns each (at least 2 layers with dry film thickness of 150 microns each for roller applications) .Acciaio: minimum 3 layers of each 150 micron / 6 mils dry film thickness.

Application equipment

We recommend using manichettei ½ '' between the pump and the spray gun to avoid pressure drops and, if possible, remove the suction hose.

Film thickness / dilution

It may be specified in a different thickness, depending on the mode of use and area of ​​use. This will alter spreading. For application by roller, it is essential to make sure that the layer of the porous film is not specified.

Catalyst

The catalyst is highly thixotropic. Add 3 basic parts to 2 parts of catalyst during the mixing.

Undocking

The mass in water must not take place before the catalysis of a week of the last layer of the product (20 ° C). 2 weeks at 10 ° C / 50 ° F

Overcoating

If you exceed the range, it is necessary to apply a thin coat of HEMPEL'S LIGHT PRIMER 45551. After prolonged exposure to the elements, before recoating completely clean the surface using high-pressure cleaning with fresh water and let dry.