International Cruiser Bright White 0,75lt Antifouling #458COL1200

International Cruiser Bright White 0,75lt Antifouling #458COL1200

International Cruiser Bright White 0,75lt Antifouling #458COL1200

Cruiser Bright White is a polishing antifouling, designed for both power and sailing boats, providing good antifouling protection in moderate to low fouling challenge areas. Packing of 0.75lt.
Price:
€39.90
Listing:
€54.27
You Save:
€14.37 (26%)

Description

Cruiser Bright White is a polishing antifouling, designed for both power and sailing boats, providing good antifouling protection in moderate to low fouling challenge areas.
PRODUCT DESCRIPTION
Cruiser Bright White is a polishing antifouling, designed for both power and sailing boats, providing good antifouling protection in moderate to low fouling challenge areas.
* General purpose bright white cruising antifouling for outstanding appearance
* Suitable for all substrates including aluminium
* Season long antifouling protection
PRODUCT INFORMATION
Colour YBC900­White
Finish Matt
Specific Gravity 1.58
Volume Solids 48%
Typical Shelf Life 2 yrs
VOC (As Supplied) 456 g/lt
VOC (EU Solvent) 291 g/kg EU Solvent Emissions Directive (Council Directive 1999/13/EC)

DRYING/OVERCOATING INFORMATION
Drying
5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Touch Dry 1 hrs 45 mins 30 mins 20 mins
Immersion 24 hrs 12 hrs 8 hrs 6 hrs
Overcoating
Substrate Temperature
5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Cruiser Bright White 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Note: Max. Immersion Times are as follows: 5­15°C ­ 3 mths; 23°C ­ 2 mths; 35°C ­ 1 mth

APPLICATION AND USE
Preparation PREVIOUSLY ANTIFOULED SURFACE
In Good Condition: Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon.
In Poor Condition: Use Interstrip to remove all traces of antifouling.

PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet.

BARE GRP Degrease with solvent or Super Cleaner. Sand well using 180­220 grade paper. Clean thoroughly and allow to dry. Pre­prime using an International primer as detailed for specific coating systems.

STEEL Degrease with solvent or Super Cleaner. Gritblast to Sa 2½ ­ near white metal surface. If gritblasting is not possible, grind the metal surface with 24­36 grit abrasive discs to a uniform, clean, bright metal surface with a 50­75 microns anchor pattern. Use angle grinder on small areas. Clean thoroughly and allow to dry. Pre­prime using an International primer as detailed for specific coating systems.

LEAD Degrease with solvent or Super Cleaner. Sand well using 120 grade paper or power wire brush. Clean thoroughly and allow to dry. Pre­prime using an International primer as detailed for specific coating systems.

WOOD/PLYWOOD Sand smooth with 80­180 and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems).

ALUMINIUM Degrease with solvent or Super Cleaner. Sand well using 24­120 grade (aluminium compatible) paper.
Coarser grades are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Pre­prime using an International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Method Apply 2 coats per season on the hull. 3 coats are required on the leading and trailing edges, waterline, rudder and keel.
This is important for best performance.
Hints Mixing Stir well before use.
Thinning Thinning is not recommended Cleaner Thinners No.3
Other Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness.
Some Important Points To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide.
Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F.
Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F.
Substrate temperature should be 3°C/5°F above dew point and maximum 35°C/95°F.
Full opacity may not be observed until second or third coat is applied, especially if applying over dark colours.
Compatibility/Substrates Suitable for use on all substrates including suitably primed Aluminium/Alloy and Zinc­sprayed metals. Can be applied direct over most types of antifoulings, provided they are in sound condition

Number of Coats 2­3 by brush/roller
Coverage (Theoretical) ­ 10.63 m²/lt
(Practical) ­ 9.2 m²/lt
Recommended DFT per coat 45 microns dry per coat
Recommended WFT per coat 94 microns wet per coat
Application Methods Brush, Roller

TRANSPORTATION, STORAGE AND SAFETY INFORMATION

Storage GENERAL INFORMATION:
Exposure to air and extremes of temperature should be avoided. For the full shelf life of Cruiser Bright White to be realised ensure that between use the container is firmly closed and the temperature is between 5°C/41°F and 35°C/95°F. Keep out of direct sunlight.

Packing of 0.75lt.